diff --git a/src/README.md b/src/README.md
index 4fb3519..cf53b00 100644
--- a/src/README.md
+++ b/src/README.md
@@ -15,7 +15,7 @@ The following topics will be covered:
 - How to write, build, flash and debug an embedded program.
 
 - Functionality ("peripherals") commonly found in microcontrollers:
-  - Digital input and output, using buttons and LEDs
+  - Digital input and output, including buttons and LEDs
 
 <!-- - Functionality ("peripherals") commonly found in microcontrollers: Digital input and output, Pulse
   Width Modulation (PWM), Analog to Digital Converters (ADC), common communication protocols like
diff --git a/src/appendix/troubleshooting.md b/src/appendix/troubleshooting.md
index c2d375e..b820635 100644
--- a/src/appendix/troubleshooting.md
+++ b/src/appendix/troubleshooting.md
@@ -90,39 +90,6 @@ The USB connection was lost.
 - Disconnect and re-connect the USB cable.
 - Re-launch OpenOCD
 
-### Can't flash the device - "Ignoring packet error, continuing..."
-
-#### Symptoms
-
-While flashing the device, you get:
-
-```
-$ arm-none-eabi-gdb $file
-Start address 0x8000194, load size 31588
-Transfer rate: 22 KB/sec, 5264 bytes/write.
-Ignoring packet error, continuing...
-Ignoring packet error, continuing...
-```
-
-#### Cause
-
-Closed `itmdump` while a program that "printed" to the ITM was running. The
-current GDB session will appear to work normally, just without ITM output but
-the next GDB session will error with the message that was shown in the previous
-section.
-
-Or, `itmdump` was called **after** the `monitor tpiu` was issued thus making
-`itmdump` delete the file / named-pipe that OpenOCD was writing to.
-
-#### Fix
-
-- Close/kill GDB, OpenOCD and `itmdump`
-- Remove the file / named-pipe that `itmdump` was using (for example,
-  `itm.txt`).
-- Launch OpenOCD
-- Then, launch `itmdump`
-- Then, launch the GDB session that executes the `monitor tpiu` command.
-
 ## Cargo problems
 
 ### "can't find crate for `core`"
diff --git a/src/setup/README.md b/src/setup/README.md
index d935cc1..43c1238 100644
--- a/src/setup/README.md
+++ b/src/setup/README.md
@@ -1,7 +1,8 @@
 # Development environment setup
 
-Dealing with microcontrollers involves several tools as we'll be dealing with an architecture
-different than your laptop's and we'll have to run and debug programs on a "remote" device.
+Dealing with microcontrollers involves several tools,
+as we'll be dealing with an architecture different than your laptop's,
+and we'll have to run and debug programs on a "remote" device.
 
 ## Documentation
 
@@ -15,8 +16,8 @@ We'll be referring to the [micro:bit hardware page][microbit] and the links foun
 
 ## Tools
 
-We'll use all the tools listed below. Where a minimum version is not specified, any recent version
-should work but we have listed the version we have tested.
+We'll use all the tools listed below. Where a minimum version is not specified,
+any recent version should work but we have listed the version we have tested.
 
 - Cargo & `rustc`.
 
@@ -51,12 +52,6 @@ $ rustc -V
 rustc 1.28.0-nightly (056f589fb 2018-06-22)
 ```
 
-### `itmdump`
-
-``` shell
-$ cargo install itm
-```
-
 ### OS specific instructions
 
 Now follow the instructions specific to the OS you are using: